The barn door should cover the opening entirely, so the installation process would be of the essence, with about an inch of overhang on each side and one inch along the top. The door should have a 1-inch gap between the floor and it when it is hanging from the railing. Installing the metal track on the wall is the first step. However, bear in mind that a backer board can also be required for the track itself. The necessary one-inch space between it and the wall may be made using backer boards. We also strongly advise installing a backer board beneath your barn door's tracking mechanism unless you have solid walls. Get the backer board ready. Cut a piece of pressure-treated timber that is one inch thick to the length and breadth of the track on your barn door. The backer board should then be covered by painting it the same color as the wall or trim. Prior to installation, completely coat the board with paint on a level surface. install sliding barn doors Choose the installation position. Find the studs behind the wall with a stud finder. Marking the studs above the entryway is necessary. Aim three to four inches above the door opening's hinge side for single barn doors, going all the way down the backer board. Find studs on both sides of the door opening for double barn doors. 
Next, mark the locations of the studs along the backer board while maintaining its level. Remember to account for the door's height when positioning the board, but leave extra room for gaps between it and the backer board and gaps between the door and the floor. Pre-drill holes along the stud locations indicated on the backer board. Use a countersink bit to drill two holes on the studs themselves. Drill starter holes at each hole along the metal track after it has been clamped to the backer board. The backer board should be mounted to the wall. Holding the backer board against the wall with help, fasten one end with a wood screw to the stud. Verify that the screw heads are barely visible above the wood's surface. Use the remaining wood screws to finish the previous step on the other side of the backer board while maintaining levelness. Last but not least, cover the screw heads with wood filler and paint them to match the board. Put the metal track in place. Align and fasten the metal tracks using the supplied hardware in the holes bored into the backer board (commonly lag bolts and washers). Make sure the bolts are well fastened and, if required, adjust with a wrench for a tighter grip. 
Level the track and mark the mounting holes on the surface of the wall if you are mounting a metal track straight to a concrete wall without using a backer board. Use a masonry bit to pre-drill the fastening holes before installing a sliding barn door on concrete. For simplicity, masonry anchors and lag bolts are included in each barn door hardware kit. The last step is to attach door stoppers to the metal track, whether using a backer board or on concrete walls. As you place each stopper on the track, tighten the pre-set screw. Buying a whole barn door kit has the advantage of including templates to assist you to identify where the equipment should go. Additionally, some barn door kits come with pre-drilled holes, skipping some of the processes. To install a full kit or to buy hardware and doors individually, you must first secure all of the parts before hanging the doors firmly. The steps are as follows: Put the rollers in place. Rollers will give your barn door the smooth motion it requires. It is essential to consult the manufacturer's instruction booklet since every sliding barn door is made differently. The rollers should, however, generally be attached by screwing into the top edge of the door or by strap hangers fastened by ornamental hardware components. Once the rollers are in place, use a speed square to make sure the strap hanger is straight. Put the door doorknob in place. 
Make sure the center of the handle is 36 inches from the bottom of the door, regardless of the kind of handle your barn door already has or that you pick, such as recessed or pulls. (Most doorknobs are placed in this manner as the norm.) Place the outside handle of the door close to the edge. But keep in mind that the door will be broader than the opening when choosing the inside handle. Because of this, you must carefully place the handle so that it has enough room to shut without slamming into the door jamb. Pre-drill the holes if you bought your barn doors separately from a kit. Before installing the handle, pre-drill each of the holes for the screws and note their locations. Using the complementary screws included with the hardware, secure the door knobs. Lift the door with help and place the wheels along the metal track. Take care not to harm the neighboring furniture, molding, or walls. Give the door another try after the wheels are in place. Ensure that it glides smoothly and accurately. The little rubber blocks, commonly known as anti-jump discs, should then be attached. Should the roller wheels ever deviate off the track, these anti-jump discs are intended to hold the door in place. Screwing each disc to the top edge of the door will secure it. Set up the door guides to the floor after the anti-jump discs. By using these guidelines, the door will be able to open without stuttering or swaying when rolling on the rollers. Note: Some sliding doors include bumper-like guides that hold the door in place from the sides or door guides that slide into a machined groove at the bottom of the door. Put the guide or guides in place, and after deciding where to put them, screw them in. 
Testing your barn doors one more time is the last step before hanging them. Make sure the doors open and shut smoothly. Pay attention to the anti-jump discs and stoppers to make sure they are in excellent working order. Keep the hardware clean by wiping it down often. To preserve the finishes, it is preferable to use a soft cloth and a gentle cleanser. While many of these spots may be cleaned down as part of ordinary room cleaning, keep in mind to also check the track for debris. Use an oil soap designed specifically for wood and wood stains on wood barn doors. Glass cleaners should be used to clean any glass inserts; strong multipurpose cleansers that include chlorine should be avoided since they might harm the hardware and wood. If any screws along the track are loose, tighten them immediately. Hardware that gets harmed should be replaced. Hardware problems might escalate into more serious problems.
💰 Tenfold your income 💎